Journey with Confidence RV GPS App RV Trip Planner RV LIFE Campground Reviews RV Maintenance Take a Speed Test Free 7 Day Trial ×
 


Reply
 
Thread Tools Search this Thread Display Modes
 
Old 09-06-2015, 05:19 PM   #1
Junior Member
 
Join Date: Nov 2013
Posts: 17
Big Gap In Front Cap And Roof Seal

I own a 2011 Redwood 36 RE.

I just discovered a significant gap where the roof is sealed to the front cap. I've used this forum to learn about roof sealants, but I'm posting because I feel my situation may be somewhat unique due to the size of the gap.

The cap-to-roof seal separation is 2-3 feet long; and as much as 1 inch high. Please refer to the picture.

When I use both hands to push down on the cap so it will come in contact with the roof; it simply pops back up exposing the gap. I can't determine if the roof has lowered in this area or whether the fiberglass cap is warped.

This leads me to believe my only option is to caulk the heck out of that opening. Would I still use Alpha Sytems or Dicor products? Self-leveling or not self-leveling? Do I remove the existing caulking before applying the new caulking. How do I clean the area prior to applying the caulking?

I'm open for any and all comments on how to remedy this problem.

Thanks, Don in Maine
Attached Images
File Type: jpg opening in rv roof seam1.jpg (58.0 KB, 67 views)
donwheeler is offline   Reply With Quote
Old 09-06-2015, 05:37 PM   #2
Senior Member
 
RomanyLife's Avatar
 
Join Date: Jun 2015
Posts: 512
That's a super bummer! I don't know if it's just the picture, but it appears that the cap is misshapen... Can't tell for sure. I have no idea how to address that, but I bet someone here will!
__________________

Living the Dream in our 2015 38RL: 1600 watts solar, 800 ah lithium, slide in slide, residential refer, washer/dryer, Moryde 8K, H rated tires, Kodiak disc brakes, Drainmaster system, SeeLevel II
Our big girl is dragged around by our 2019 RAM 3500 Limited DRW
Grateful Veterans, Proud Americans, Devoted Partners, Parents and Grandparents!
LOVE the Full Time RV Life @OurRomanyLife
RomanyLife is offline   Reply With Quote
Old 09-06-2015, 06:33 PM   #3
Senior Member
 
GA1817's Avatar
 
Join Date: Sep 2014
Posts: 378
I had a small slit on my rear cap but it was only a few inches long. I too pushed it down and it popped back. I have thought about using eternabond tape and run it across the whole seam and then apply caulk. You would think the cap would be screwed into the deck. I eagerly want to hear ideas others have on this.
__________________
Dean & Cindy (Go DAWGS)
2013 Ram 3500 CC DRW 4.10 "Plain Jane"
(RIP "Struck by Lightning")
B&W 3600 Hitch 25K/6.25k
2012 36RL, Disc Brakes, G614's, 7K axles, Combo WD, Awning Toppers
Full Time Since April 1 2015:)!
GA1817 is offline   Reply With Quote
Old 09-06-2015, 07:24 PM   #4
Junior Member
 
shepcody's Avatar
 
Join Date: Jun 2012
Posts: 9
Send a message via AIM to shepcody
Water is getting in under the top cap molding and rusting the screw threads. Clean off all the old sealant you can and remove a screw. You may not find any threads on it. Pre drill cap molding (larger than #8 screw) and add new screws next to old ones. You can pre drill for the new screws if you want to. Clean off old sealant with an old dull putty knife and seal with alpha sealant. I found it on line last year as I have a 2013 34SK and had to spot seal roof.
__________________
Dick and Donna
shepcody is offline   Reply With Quote
Old 09-06-2015, 08:54 PM   #5
Senior Member
 
Join Date: Nov 2013
Posts: 649
I had a 2012 36RE and the same thing happened. The screws that go thru the molding and the alpha roofing into a cross member broke. The screw broke from? excessive flexing was the best guess.
__________________

Ron & Margaret
2014 Ram 3500 DRW 6.7, Aisin, 4.10
"Pequod" 2015 Redwood 38GK
Titan Guy is offline   Reply With Quote
Old 09-06-2015, 09:53 PM   #6
Senior Member
 
Join Date: Dec 2011
Posts: 165
Cap Seal

One thing you can do is cut the seal where it is coming up to relieve the pressure. Then push the seal back down and take a piece of eternabond tape and place over the seal where you cut it. Then take Dicor Self-leveling sealant and reseal the whole cap seal leaving the old sealant in place. When I did mine I used 8 tubes on self leveling sealant.
__________________
John & Sherry
2012 Redwood RE
2004 Chevy 3500
Camphost
j1251b is offline   Reply With Quote
Old 09-07-2015, 01:28 AM   #7
Senior Member
 
travelin' texans's Avatar
 
Join Date: Sep 2012
Posts: 3,353
There should be a metal strip joining the cap & roof & as stated previously the screws rusted off or are broke, I'd clean old caulk off as best I could to remove old screws if possible & replace with larger screws, preferably stainless steel, & recaulk the crap out of it. That's what I'd do! Right or wrong??
__________________
Danny & Linda
Full-timed 10+ years
Former '13 FB owner
Traded '13 GMC Denali DRW D/A
Currently rv & truckless
Replacement undetermined
travelin' texans is offline   Reply With Quote
Old 09-07-2015, 01:33 AM   #8
Senior Member
 
Shane Wood's Avatar
 
Join Date: Nov 2014
Posts: 2,032
Send a message via AIM to Shane Wood Send a message via MSN to Shane Wood Send a message via Yahoo to Shane Wood
RIGHT
You hit the nail on the head
__________________
2015 36RL pushing a 2015 Denali
Shane Wood is offline   Reply With Quote
Old 09-07-2015, 01:43 AM   #9
Junior Member
 
Join Date: Nov 2013
Posts: 17
Cap Seal

Thanks to everyone for the comments and suggestions.

Don in Maine
donwheeler is offline   Reply With Quote
Old 09-07-2015, 02:34 AM   #10
Senior Member
 
Rick and Mindy's Avatar
 
Join Date: Feb 2013
Posts: 1,444
Don, that Eternabond tape is incredible stuff. I got tired of having very small water leaks in my closet area of my prior fifth wheel so I put eternabond completely across the front seam where the cap met the roof and bingo, no more leaks. Just some words of caution though, be sure you place the eternabond where you want it because once you put it down you can't re-position it. I would definitely try to put new screws in the trim to keep it down before using eternabond. Eternabond is also what Redwood uses on the slideout roofs.
__________________
Rick and Mindy
Retired
2013 Redwood 31SL, 2011 Ford F350 SRW, 6.7, Crew Cab with Firestone Bags, Titan Disc Brakes
Rick and Mindy is offline   Reply With Quote
Old 09-07-2015, 12:59 PM   #11
Senior Member
 
Campers's Avatar
 
Join Date: Mar 2012
Posts: 427
We had the same problem with our FL. The dealer removed the caulking, cleaned the area and rescrewed the cap to the coach. They recalled and have not had any issues in 3 years. They said it was caused by not enough screws in the first place and the torquing of the cap against the body. Good luck.
__________________
Bud & Lois
Campers is offline   Reply With Quote
Old 09-11-2015, 02:07 AM   #12
Junior Member
 
Join Date: Sep 2014
Posts: 9
When I purchased my 2014, the front and back caps had what looks like Alpha Systems Superflex butyl tape or something similar over the seam (where the cap and alpha roofing material meet), and then the alpha superflex sealant around the edge of the tape. I don't know if it came this way from the factory or if it was done by my dealer ........ but its seems like a good idea.
Moos is offline   Reply With Quote
Old 09-11-2015, 02:35 PM   #13
Senior Member
 
Rick and Mindy's Avatar
 
Join Date: Feb 2013
Posts: 1,444
Quote:
Originally Posted by Moos View Post
When I purchased my 2014, the front and back caps had what looks like Alpha Systems Superflex butyl tape or something similar over the seam (where the cap and alpha roofing material meet), and then the alpha superflex sealant around the edge of the tape. I don't know if it came this way from the factory or if it was done by my dealer ........ but its seems like a good idea.
It's probably Eternabond tape and probably put on by a dealer or prior owner. I can tell you, the first time I see any sign of a possible leak in those seams, they will be covered with Eternabond. I question why Redwood doesn't use that on those areas anyway since it seems to be good enough for the slide roofs. That seems to be the go-to product for manufacturers these days to seal their slide roofs. Eternabond, if I remember correctly, recommends that the tape be caulked along all edges, something that I have not seen manufacturers doing.
__________________
Rick and Mindy
Retired
2013 Redwood 31SL, 2011 Ford F350 SRW, 6.7, Crew Cab with Firestone Bags, Titan Disc Brakes
Rick and Mindy is offline   Reply With Quote
Old 09-11-2015, 02:41 PM   #14
Senior Member
 
Rick and Mindy's Avatar
 
Join Date: Feb 2013
Posts: 1,444
One of the issues I had early on with my Redwood was the Eternabond tape on the slide roofs. If you get up on a ladder and look closely at the front (outside) corner of the slide roofs (where the Eternabond rolls down onto the side you will see a very sharp point on that corner which end ups poking through the tape. They replaced the tape on mine at the Service Center but it still seems to be doing the same thing which I believe will be a possible leak area in the future. My plan is to file that sharp point down and then cover that corner with an additional piece of tape.
__________________
Rick and Mindy
Retired
2013 Redwood 31SL, 2011 Ford F350 SRW, 6.7, Crew Cab with Firestone Bags, Titan Disc Brakes
Rick and Mindy is offline   Reply With Quote
Old 09-18-2015, 12:52 AM   #15
Junior Member
 
Join Date: Nov 2013
Posts: 17
Sealant Applied To Seam

Here's an update on what I've done so far to correct the cap-to-roof gap.

The responders to my original post were right on target.
Just over half the screws on bedroom slide side had broken.

I removed all of the old sealant from the seam.
I put in several stainless steel screws in at 3-4 inch intervals.
Then I covered the seam with Dicor self-leveling lap sealant (see attached picture). I didn't put an abundant amount on (yet). I put on just enough to cover exposed screw heads and the metal strip. I had a concern that if I went strictly with the Eternabond tape method; exposed metal might ultimately damage the tape. Don't know if that's a valid concern or not.

I could use some advice on how to proceed from here.
1. I could just add a whole bunch more of sealant.
or
2. Once the sealant has hardened; cover the seam and existing sealant with 6 or 8 inch wide Eternabond tape. I just don't know if Eternabond tape can be applied over relatively new sealant. By the way, how long does it take for the sealant to harden?

Thanks,
Don in Maine
Attached Images
File Type: jpg Sealed RV Roof.jpg (33.4 KB, 39 views)
donwheeler is offline   Reply With Quote
Old 09-18-2015, 01:11 AM   #16
Senior Member
 
GA1817's Avatar
 
Join Date: Sep 2014
Posts: 378
Looks good Don. How hard was it to remove the old seal. Did you use heat?
GA1817 is offline   Reply With Quote
Old 09-18-2015, 02:26 AM   #17
Senior Member
 
atom ant's Avatar
 
Join Date: Feb 2013
Posts: 7,101
From what I can see, looks like you are done! Looks like how the factory does it.
__________________
Brad & Dory - Lone Tree, CO
CURRENT - 2013 Itasca Meridian 42E/2013 Wrangler 4dr Sahara
SOLD - 2014 Redwood 36RL/2014 F350 DRW
atom ant is offline   Reply With Quote
Old 09-18-2015, 02:13 PM   #18
Junior Member
 
Join Date: Nov 2013
Posts: 17
I did not have to use heat to remove the caulking. However, the RV had been sitting in the driveway with the sun shining on it all day.
It probably took me about an hour to remove all of it.
I carefully used a putty knife to break it loose from the surface it was adhered to; then gently pealed it off.
donwheeler is offline   Reply With Quote
Old 09-18-2015, 05:55 PM   #19
Senior Member
 
travelin' texans's Avatar
 
Join Date: Sep 2012
Posts: 3,353
I agree with Brad except the part "it looks like factory", it looks better than factory. I'd call it good & see how it holds up, you can always add more if needed.
__________________
Danny & Linda
Full-timed 10+ years
Former '13 FB owner
Traded '13 GMC Denali DRW D/A
Currently rv & truckless
Replacement undetermined
travelin' texans is offline   Reply With Quote
Old 09-18-2015, 05:57 PM   #20
Senior Member
 
travelin' texans's Avatar
 
Join Date: Sep 2012
Posts: 3,353
Also, depending on the sealant you used, it may never harden, mine is still very soft.
__________________
Danny & Linda
Full-timed 10+ years
Former '13 FB owner
Traded '13 GMC Denali DRW D/A
Currently rv & truckless
Replacement undetermined
travelin' texans is offline   Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


» Featured Campgrounds

Reviews provided by

Powered by vBadvanced CMPS v3.2.3
Disclaimer:

This website is not affiliated with or endorsed by Redwood RV or any of its affiliates. This is an independent, unofficial site.


All times are GMT +1. The time now is 01:01 PM.


Powered by vBulletin® Version 3.8.8 Beta 1
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
×